
How to Use a Nintendo Switch With Starlink: NAT and Multiplayer Checks
Tips & Tricks
Nintendo Switch can play online over Starlink, but a failed match or a strict NAT result does not automatically mean the dish is faulty. Start with the console's own connection test, then separate local Wi-Fi, router layout and Starlink's upstream NAT before changing settings.
Independent guide: Starlink Tips is not part of Starlink or Nintendo. Console menus, router options, Starlink hardware and service behaviour can vary by model, country and software version.
The short answer
Use this order:
- Check for a Starlink outage or equipment alert in the Starlink app.
- On the Switch, open System Settings > Internet > Test Connection and record the NAT type, download speed and upload speed.
- Repeat the test close to the Starlink router, then test the dock by Ethernet if your Switch model and dock support it.
- Confirm that only one router is providing the main Wi-Fi, DHCP and firewall service.
- If a second router is installed, test access-point mode or a supported Starlink bypass layout instead of stacking routers.
- If the router WAN address is in the shared
100.64.0.0/10range, a port-forwarding rule in your home cannot remove Starlink's provider-side CGNAT. - Change one thing at a time and run the Switch test again.
Nintendo describes NAT Type A as the most favourable result for peer-to-peer communication and Type B as broadly compatible. Stricter results can limit which players or games the console can reach. A good NAT result does not guarantee that every game, friend or Nintendo service is available.
Record a clean baseline
Before changing the router, create a result you can compare later.
- Open the Starlink app and check for a service interruption, obstruction warning or equipment alert.
- Pause game downloads, cloud backups, streaming uploads and other large transfers.
- Restart the Switch once.
- From the HOME Menu, choose System Settings > Internet > Test Connection.
- Record Internet Connection, NAT Type, Download Speed and Upload Speed.
- Try the same online game or friend connection twice. One failed matchmaking attempt is not enough to prove a NAT fault.
- Note whether the problem affects every game or only one title or player.
Nintendo's connection test shows the active network name and SSID as well as the NAT result. Keep a private note of the result, but do not post your global IP address or Wi-Fi credentials in a support forum or screenshot.
Improve the local connection first
A Switch can show a poor result because the local wireless link is weak or the network is busy. Starlink's internet path cannot repair a marginal Wi-Fi connection between the console and the router.
Try the following controlled comparison:
- Place the Switch or dock close to the Starlink router for the test.
- Keep the console away from large metal objects, speakers and other electronics that may interfere with Wi-Fi.
- If your setup supports wired networking, connect the dock to the router with Ethernet. Some Switch docks have a built-in LAN port; other models may need a compatible LAN adapter, and a Switch Lite can require additional hardware for wired use.
- Run Test Connection again.
- Compare the NAT type and speed with the original baseline.
- Play or matchmake for long enough to reproduce the original problem.
If wired networking improves stability but not the NAT type, the wireless link was part of the problem but the router or upstream path still determines the NAT result. If the NAT type stays the same and only one game fails, check that game's service status and support guidance before changing the home network.
Check for two routers
Double NAT means that two routers are translating traffic inside the same home. A common layout is:
Starlink dish -> Starlink router -> gaming or mesh router -> Switch
This can happen after adding a mesh system or gaming router without changing its operating mode.
On the second router, look at its WAN, Internet or external IPv4 address:
192.168.x.x,10.x.x.xor172.16.x.xthrough172.31.x.xusually means the second router is receiving a private address from another router.100.64.0.0through100.127.255.255is commonly a provider-shared CGNAT range.- A mismatch between the router WAN address and the address shown by an external IP-check service is a clue that another translation layer exists. VPNs and privacy relays can also change what you see, so treat this as evidence rather than proof.
If the Switch connects directly to one Starlink-managed router, there may be no local double NAT to remove. Decide which device should own Wi-Fi, DHCP, firewall rules and routing before changing anything.
Choose one router layout
Keep the Starlink router in charge
This is the simplest arrangement for many homes.
- Connect the Switch to the Starlink-managed Wi-Fi or Ethernet network.
- Put the additional mesh or Wi-Fi device into Access Point, Bridge or equivalent mode if you still need coverage.
- Leave DHCP and routing enabled on the Starlink router.
- Restart the router and Switch, then run Test Connection again.
The exact port and mode names depend on the second device. Follow its current documentation rather than guessing.
Let your own router manage the home network
Use this when you need advanced firewall, mesh, VPN or traffic-management features.
- Confirm that your Starlink kit provides the wired connection your router needs.
- Connect the Starlink Ethernet path to the router's WAN port.
- Enable Starlink Bypass Mode only when your kit and layout support it.
- Configure the router to obtain its WAN address automatically unless its documentation says otherwise.
- Put Wi-Fi, DHCP, firewall rules and device reservations on that router.
- Reconnect the Switch and run its test again.
Record the working layout first. Bypass mode can change which Starlink router features are active, and a factory reset is not a good first response to a NAT warning.
Keep two routed networks deliberately
This can be valid for a special network design, but it makes game discovery, automatic port mappings and troubleshooting harder.
- Use different private address ranges on the two routers.
- Keep the Switch and the router responsible for its gateway on the same routed network where possible.
- Document which router owns each rule.
- Do not add a third routing layer just to improve Wi-Fi coverage.
For most households, one main router plus access points is easier to operate.
Test UPnP cautiously
UPnP lets the Switch or a game request temporary port mappings from the router. It may improve convenience, but it also allows devices on that network to ask for inbound mappings automatically.
If you choose to test it:
- Enable UPnP only on the router that provides the Switch's gateway.
- Avoid running competing UPnP services on multiple routers.
- Restart the router and Switch.
- Run the Switch connection test again.
- Test the same game or friend connection.
- Turn UPnP off or remove stale mappings if you do not trust every device on the network.
UPnP cannot create an inbound path through Starlink provider CGNAT. It changes mappings on the routers you control; it does not control the upstream Starlink address.
Understand when port forwarding will not help
Traditional port forwarding needs an inbound path to your router. If your router receives a shared 100.64.0.0/10 address and does not match the public address seen from the internet, Starlink or another upstream provider is translating traffic before it reaches your home.
In that situation:
- A correct port-forwarding rule can still fail.
- Forwarding the same port on two local routers does not remove provider CGNAT.
- Changing DNS does not change the NAT path.
- A permanent DMZ setting does not bypass provider CGNAT and exposes the console more broadly than necessary.
- Forwarding every port to the Switch is not a safe troubleshooting step.
Some Starlink plans or service types may offer a public IPv4 option in some markets. Check the plan and IP policy attached to your own account. A public address may still be dynamic, and it is not a security feature by itself. Keep the router firewall enabled and test only the service you need.
If the Switch reports a strict result
Use the result to choose the next test rather than treating it as a verdict.
NAT Type A or B
The home network is generally in a good position for peer-to-peer play. If a game still fails:
- Test the same game after pausing large transfers.
- Check for a game or Nintendo service outage.
- Compare wired and nearby Wi-Fi results.
- Try a second friend or game to see whether the issue is specific to one service.
- Check the other player's network if you can reproduce the problem only with that person.
NAT Type C or D
A stricter result can limit matchmaking. First check for local double NAT, then test access-point mode or the correct single-router layout. Do not start with a permanent DMZ or a large set of forwarded ports.
Nintendo's support guidance also suggests testing with IPv6 disabled on the console when a stricter NAT result is causing connection problems. Treat that as a controlled test:
- Open System Settings > Internet > Internet Settings.
- Select the saved network and choose Change Settings.
- Find IPv6 Connection and turn it off temporarily.
- Run Test Connection and record the result.
- Try the same game or friend connection.
- Restore the previous setting if it makes no improvement or causes another device or service to behave differently.
Do not disable IPv6 on the whole Starlink network just because the Switch test is strict.
NAT Type F
Type F indicates that peer-to-peer communication is being blocked or cannot complete. Recheck the Starlink service status, test the Switch on a clean local connection, and confirm that the router layout is not adding an avoidable translation layer. Then test the console's IPv6 setting as described above.
If Type F persists after a single-router or supported access-point layout, record the console result, router WAN address and affected game before contacting the ISP, router maker or Nintendo. Do not factory-reset every device at once; it will remove evidence about which layer is failing.
A repeatable troubleshooting checklist
Run this sequence after each change:
- Check Starlink service and equipment status.
- Pause large downloads and uploads.
- Test the Switch close to the router.
- Test the dock by Ethernet if available.
- Record NAT type, download speed and upload speed.
- Confirm which device provides the Switch's gateway and DHCP.
- Check the second router's WAN address if one exists.
- Test access-point mode or a supported bypass layout.
- Test UPnP on only the main router, if you accept its security trade-off.
- Test the console's IPv6 setting only as a controlled comparison.
- Try a second game or friend connection.
- Remove changes that did not help.
Avoid these common mistakes
- Do not assume every failed match is a Starlink outage.
- Do not change Wi-Fi, router mode, DNS, IPv6 and port rules all at once.
- Do not enable UPnP on several routers and expect the mappings to pass cleanly.
- Do not forward every port to the Switch.
- Do not leave the Switch in a permanent DMZ.
- Do not factory-reset Starlink equipment before recording the current layout.
- Do not publish a screenshot containing your global IP address, Wi-Fi password or account details.
- Do not assume NAT Type A guarantees that a particular friend, game server or Nintendo service is available.
Bottom line
Start with the Switch's own connection test and a nearby or wired comparison. If a second router is creating local double NAT, simplify the layout with access-point mode or a supported Starlink bypass arrangement. If the router remains behind Starlink's shared CGNAT, home port forwarding cannot remove that upstream layer. Keep changes reversible, test one variable at a time, and use stricter NAT results as evidence for the next check rather than a reason to expose the console.
For the wider networking background, see Starlink NAT Type on PlayStation and Xbox: Diagnose Strict or Moderate Multiplayer, Starlink Double NAT: How to Diagnose It and Pick the Right Fix and Starlink CGNAT and Port Forwarding: Remote Access Options.
Official reference: Nintendo Switch internet connection test and Nintendo NAT troubleshooting.
Get One Month of Starlink Free
Order through my referral link and activate your service. Your second month of Starlink service will be free. Current terms are shown at checkout.
Starlink Tips is independent and may receive a referral reward. Check the offer shown for your order.